|
Drivers Cup Holder & 32oz Insulated Mug
The drivers cup holder mounts on the right side on the handle bar. It screws into the threadhole that has a plastic plug is in or where you can put a helmet holder. It is above the kill switch. It comes with a 32oz insulated mug. And it is powder coated in black.
$24.95
|
|
Drivers' Footpegs with Offset Mounts and Magnum Quick Clamps
These highway pegs utilize our unique offset mount to allow riders a range of adjustment not possible with other clamp-on style highway pegs. The offset can be rotated 360 degrees in a 4" diameter circle to accommodate tall, short, or average height riders. These can be installed on any 1" round tubing (frames or engine guards). But it is important to keep in mind that the footpeg itself will emd up perpendicular to the bar to wich it is mounted.
$119.95 |
|
Cooler / Small Luggage Rack
It measures 10" X 14". The cooler/luggage rack mounts into the receiver of the trailer hitch. It is secured with the same pin that holds the receiver ball in place for your trailer. It is powder coated in black.
$69.95 |
| 
|
Cooler / Small Luggage Rack - New Design
This is a new design, which is much easier to install and to remove. It uses the same pin that holds the receiver and ball on the trailer hitch. Just remove the ball and receiver and insert the rack and put the pin in place. You are then ready to go on a picnic or a weekend getaway. The luggage/cooler rack measures 10x14 inches and is powder coated in black. This one hitch will only fit into Marvellas trailer hitch.
$69.95
|
|
Adjustable Passenger Footrest
The passenger will be more comfortable with the adjustable foot rest because it gives the foot a 5" raise and 6" forward. The pegs fold away when not in use and are simple to install.
They are made from the best quality steel by Marv, himself. The footrests are chrome plated. The pegs (where your feet rest on) are top quality also.
$139.95 |
|
Trailer Hitch
Receiver hitch is 1 inch and comes off with one pin. It mounts without drilling extra holes.
The hitches are made of the top quality steel, by Marv, himself in his shop. When the hitch is completed, it is powder coated which makes them chip & rust restistant and won't scratch.
$149.95
|
|
Tail Light ON SALE
Extra tail light for the Kawasaki VoyagerXII or any other 1" receiver. It slides into the receiver of the Marvellas trailer hitch. It has 10 LED lights which is also a brake and tail light, measures 3 1/2" X 8". You can connect it to the trailer lights plug-in. It comes with a chrome bezel around and the metal is powder coated.
The tail light is so easy to install. All you have to do is remove the receiver with the trailer ball and slide the light receiver in to the trailer hitch and connect the electric plug. Connect the wire to the plug, "you must furnish". Then put plugs together and you are ready to ride.
$59.95 |
|
Trunk Extenders
Give your passenger a little more room. We have a trunk extender, It is adjustable and can slide back another 3". It is made of 1/4" steel and is completely powder coated. It mounts with the trunk brackets.
When you get your Kawasaki VoyagerXII from the factory the trunk will adjust back about 3". Now with our extender it will go back about another 3". It will give your passenger more room and a more comfortable ride. Longer bolts and instructions will come with the extenders.
$45.00
|
|
Passenger Cup Holder
The Cup Holder comes with an insulated 32 ounce drinking Cup with a snap-on lid and straw for easy drinking. One Cup comes with every Cup Holder purchased.
The picture shows the Passenger Cup Holder on the right side of the motorcycle
The Passenger Cup Holder can be attached to the right or left side it goes between the handle and the frame beside the passenger seat.
You can order additional Cups if so desired at a cost of $9.95 each.
$24.95 |
